COB led strip 4mm 480 leds / m 525 Lumens / m
Ref : COB4MM [#42]Accessories to compose your kit
Led strips accessories
Products guaranteed for 3 or 5 years
Return within 14 days
This COB led strip allows you to create a light decoration with totally equal diffusion over its entire length.
A modern decor present in contemporary homes, lobbies, hotels or to enhance a staircase.
The only 4mm wide strip is powered by 12V DC and can be cut every 25mm.
Not waterproof, it can only be used indoors.
Compose your ready-to-use kit
Ribbon only |
For the ribbon to work, you must have a minimum 12V 30W power supply . If you don't already have one, you need to add a power supply to the must-have accessories. Otherwise, you can purchase the ribbon on its own. |
Power supply + ribbon kit + |
Minimal kit to operate your led strip. It connects to the 230V sector and the led strip to the 12 / 24V output of the power supply. Add the power supply in the list of accessories. |
Power supply + drive + ribbon kit + + |
To compose this kit, you must add to the accessories:
|
Power supply kit + Wifi dimmer + ribbon + + |
To compose this kit, you must add to the accessories:
|
Power supply kit + DMX dimmer + ribbon + + |
To compose this kit, you must add to the accessories:
LTech brand controller intended for professionals for intensive and durable use . |
Supply voltage | 12V DC |
Type of led | COB |
Number of leds per meter | 480 |
Colors | Natural white 4000K Warm white 2700K, cold white 6000K red, green, blue, yellow. |
Brightness | 525 Lumens per meter (in white) |
Efficiency | 105 Lumens per Watt |
Consumption | 5W per meter |
Dimmable | Yes (PWM) |
Attenuation | 2% after 6000 hours |
CRI | 90 |
Lighting angle | 120 ° |
Lifetime | 50,000 hours (at 45 ° C) |
Waterproofing | Not sealed IP20 |
Dimensions | 5000 x 4 x 1.6 mm |
Cutout | Every 25 mm |
Temperature range | - 25 to 45 ° C |
PCB | 1 oz (35u) copper |
Adhesive | 3M VHB |
Certifications | CE, RoHS EN55015: 2013 / A1: 2015 EN61547: 2009 EN61000-3-2: 2014 EN61000-3-3: 2013 |
Guarantee | 3 years |
Wiring of white ribbon with single color
ribbonsThese headbands, the simplest, only have 2 threads (+ and -).
They can be connected directly to the 12 or 24V power supply. In this case, the wall switch in your home will be used to turn the lighting on and off.
They can be coupled to a dimmer to turn on, off and vary the brightness with a remote control.
With the exception of certain models (specified in the product sheet), LED strips can only have a maximum length of 5 meters.
Beyond this length, there would be a loss of light intensity after the first 5 meters.
To overcome this, it is possible to have several lengths of 5 meters (or less), one after the other, by connecting them in parallel to the power supply or to the controller.
Here is the wiring diagram of several bands with the use of a dimmer. The latter will act on all the ribbons, including those connected after the amplifier.
Precautions to be taken when handling and installing an led tape
The led strips can be bent lengthwise by describing a radius of at least 5 cm.
Under no circumstances can they be folded sideways.
If you have to make 90 ° angles, it is imperative to cut the tape into sections and connect them, either with a suitable angle connector, or better, by soldering flexible cable (flat ribbon) between the 2 sections.
Do not bend the led strips or subject them to distortion:
Choosing a led strip
How to choose the led strip best suited to your needs?
To quickly and easily find the led strip that best suits
your lighting project, consult our guide